15 Degree Frame 3 or 4 Link Upper Control Arm Mount - Adjustable / Wide
Use these to easily mount your upper control arms to the frame of your rig!
This unique design allows for much simpler installation compared to other UCA brackets on the market and here is why:
After you find it’s final location with test fitting, each piece can be welded in separately. The main C section can be welded in alone which makes weld joint access much better than trying to weld a bracket in that is fully assembled already. Next you just place the inner tab in it’s grooves so there is no guess work or trouble holding it while tacking it in place. Then you can weld that part in and repeat the process for the outside tab.
Mounting width to accommodate the common 2.625” wide rod ends. This comes with 9/16” bolt holes but can be drilled out to accommodate larger bolts if desired. 3” of height adjustability, in 1” increments allows you to have full control of your suspension setup. The side is flat and meant to be welded to a flat frame surface. These brackets can be mounted on either passenger or driver side since they are symmetrical.
Made from laser cut 1/4” steel and CNC bent for precise and consistent parts.
We recommend adding 1 or 2 of our 75 degree gussets to the rear of the bracket to give it extra strength! You can add that on with the option below.
Note: 1 mount per order. No hardware or rod ends supplied.
Read the blog post about these and watch the YouTube video!
Please allow 2-3 weeks for shipment as we are still preparing this batch.
Use these to easily mount your upper control arms to the frame of your rig!
This unique design allows for much simpler installation compared to other UCA brackets on the market and here is why:
After you find it’s final location with test fitting, each piece can be welded in separately. The main C section can be welded in alone which makes weld joint access much better than trying to weld a bracket in that is fully assembled already. Next you just place the inner tab in it’s grooves so there is no guess work or trouble holding it while tacking it in place. Then you can weld that part in and repeat the process for the outside tab.
Mounting width to accommodate the common 2.625” wide rod ends. This comes with 9/16” bolt holes but can be drilled out to accommodate larger bolts if desired. 3” of height adjustability, in 1” increments allows you to have full control of your suspension setup. The side is flat and meant to be welded to a flat frame surface. These brackets can be mounted on either passenger or driver side since they are symmetrical.
Made from laser cut 1/4” steel and CNC bent for precise and consistent parts.
We recommend adding 1 or 2 of our 75 degree gussets to the rear of the bracket to give it extra strength! You can add that on with the option below.
Note: 1 mount per order. No hardware or rod ends supplied.
Read the blog post about these and watch the YouTube video!
Please allow 2-3 weeks for shipment as we are still preparing this batch.
Use these to easily mount your upper control arms to the frame of your rig!
This unique design allows for much simpler installation compared to other UCA brackets on the market and here is why:
After you find it’s final location with test fitting, each piece can be welded in separately. The main C section can be welded in alone which makes weld joint access much better than trying to weld a bracket in that is fully assembled already. Next you just place the inner tab in it’s grooves so there is no guess work or trouble holding it while tacking it in place. Then you can weld that part in and repeat the process for the outside tab.
Mounting width to accommodate the common 2.625” wide rod ends. This comes with 9/16” bolt holes but can be drilled out to accommodate larger bolts if desired. 3” of height adjustability, in 1” increments allows you to have full control of your suspension setup. The side is flat and meant to be welded to a flat frame surface. These brackets can be mounted on either passenger or driver side since they are symmetrical.
Made from laser cut 1/4” steel and CNC bent for precise and consistent parts.
We recommend adding 1 or 2 of our 75 degree gussets to the rear of the bracket to give it extra strength! You can add that on with the option below.
Note: 1 mount per order. No hardware or rod ends supplied.
Read the blog post about these and watch the YouTube video!
Please allow 2-3 weeks for shipment as we are still preparing this batch.
